The claim: an elastic cover kills sling rattle
The pitch is simple: wrap your sling hardware in elastic and the metallic clink against your rifle goes away. That's the promise behind Sling Silencers, sold as a set of two elastic covers. The question is whether that promise holds up, and for which setups.
Here's the honest answer up front: these covers address one specific noise source — metal-on-metal contact between HK-style sling hooks and the mounts they sit against. They are not a universal silencer for every rattle your sling can make. Whether they're worth it depends entirely on which hardware you're running.
What Sling Silencers actually cover
Sling Silencers are elastic covers that slip over sling hardware. The catalog describes them as reducing noise signature and damage by cushioning the contact point between hardware and your rifle. They're sold as a set of two, which covers both ends of a typical two-point sling.
That's the whole mechanism: a soft barrier between two hard surfaces. There's no magic dampening material or locking mechanism. If your noise comes from hooks knocking against sling mounts or scratching the finish, a barrier is exactly the right tool. If your noise comes from somewhere else, it isn't.
What the product record confirms
- Sling Silencers: Sold as a set of two elastic covers. Two covers match a two-point sling, so you can treat both hook ends without buying twice.

Sling Silencers - Sling Silencers: Used primarily on HK style hooks and not meant for use on QD style sling swivels. This is the compatibility line that decides whether the product applies to your setup at all.
- Sling Silencers: Available in Multicam, Multicam Black, Coyote Brown, Ranger Green, and Black. Color choice lets the cover blend with your sling and rifle rather than stand out as an add-on.
Where the claim holds — and where it doesn't
If you run HK-style hooks, the claim is credible. The cover sits between the hook and the mount, so the metal contact that produces the clink is buffered. The same barrier that reduces noise also reduces scratching, which is the second half of the product's stated purpose.
If you run QD-style sling swivels, the claim doesn't apply. The product record explicitly says these covers are not meant for QD swivels. That's not a knock on the product — it's a fit boundary. Buying them for a QD setup and expecting quiet is the actual myth here.
And if your rattle comes from a loose sling mount, a buckle, or hardware elsewhere on the rifle, an elastic cover on the hook won't touch it. The covers only address the surfaces they physically sit between.
Sling Silencer pros and cons, stated plainly
- Pro: targeted noise reduction: Directly addresses hook-on-mount contact, which is a common source of metallic rattle.
- Pro: finish protection: The same elastic barrier that cushions sound also cushions contact that can scratch your rifle.
- Pro: low-cost experiment: At a catalog price of USD 5.60 for a set of two, trying them is a small commitment compared with swapping sling hardware.
- Con: narrow compatibility: Not meant for QD-style sling swivels, so a large share of modern sling setups are outside the intended use.
- Con: not a whole-sling fix: Covers the hooks only. Other rattle sources — mounts, buckles, attachments — are unaffected.
- Con: no published durability data: The supplied information doesn't state a service life or replacement interval for the elastic, so treat wear as something to monitor rather than predict.
Building a quiet sling setup around them
A quiet sling setup starts with identifying where the noise actually comes from. Unclip or loosen the sling and move it deliberately. If the clink happens where the hook meets the mount, Sling Silencers are aimed at exactly that. If it happens at a buckle or a loose attachment, fix that source first — covers won't help.
Once you've confirmed hook contact is the culprit, install the covers on both hook ends and check that they sit fully over the contact area rather than bunching to one side. The supplied information doesn't include installation steps beyond the covers' intended placement on HK-style hooks, so fit them so the elastic fully separates hook from mount and recheck after the sling settles.
For hunting and other quiet-carry use, the goal isn't a silent sling — it's removing the noises you can control. Hook rattle is one you can. Treat the covers as one fix in a sequence, not a finish line.
So, is a sling silencer worth it?
Yes, if you run HK-style hooks and the rattle you're chasing is hook-on-mount contact. The product does what it says within that scope, the set of two covers both ends, and the catalog price makes it a low-risk test.
No, if you run QD swivels — the product isn't meant for them — or if your noise comes from anywhere other than the hook contact point. In those cases the money is better spent on the actual source of the rattle.
The myth worth busting isn't that Sling Silencers don't work. It's that they work everywhere. They're a specific fix for a specific interface, and they're honest about that in their own compatibility note.

