Back to Blog
How-to Guides 2026-11-18 LOYAL TO THE MISSION 0 views

KnifenookTM Setup: Mounting a Dedicated Knife Platform

KnifenookTM Setup: Mounting a Dedicated Knife Platform

A step-by-step guide to placing the KnifenookTM wedge platform on your carrier, matching sheath hole spacing, and choosing hardware that actually fits.

The KnifenookTM is a platform, not a pouch

The KnifenookTM is a wedge-style knife mounting platform that lets you place a knife in a variety of locations on a carrier. It is not a pouch with a built-in sheath. Instead, it gives you a rigid, laser-cut thermoplastic base that sandwiches into hook-and-loop fields and accepts a sheath you already own.

That distinction shapes the whole setup. You are not choosing a pouch size; you are matching your sheath's hole pattern to the platform and finding a loop field where the wedge sits flat. The steps below follow the supplied product record, and where the record is silent, I say so rather than guess.

What the platform gives you to work with

  • Knifenook™: Constructed with rigid laser cut thermoplastic A stiff base keeps the sheath from folding or shifting when you draw, which is the main reason to use a platform instead of strapping a sheath directly to webbing.
    Knifenook™
    Knifenook™
  • Knifenook™: Fits a variety of sheaths up to 3.0” wide Measure your sheath's widest point before ordering. A sheath wider than this will overhang the platform and may not sit securely.
  • Knifenook™: 0.5” vertical hole/slot spacing This is the pattern your sheath's mounting holes need to align with. Check your sheath's hole spacing against this figure before you commit.
  • Knifenook™: The hole/slot spacing fits a majority of kydex knife sheaths Kydex sheaths are the primary intended match, but "majority" is not "all." Test-fit your sheath before relying on the mount.

A supported mounting sequence

The record describes where the platform can go and what hardware ships with it, but it does not include a manufacturer torque spec, thread-locking instruction, or a required order of operations. The sequence below is a practical assembly order built only from the supplied facts.

  1. 1. Measure your sheath: Confirm the sheath is no wider than 3.0” at its widest point and that its mounting holes line up with 0.5” vertical spacing. If either check fails, the KnifenookTM is not the right platform for that sheath.
  2. 2. Pick a loop field: The platform sandwiches in Kangaroo-style pouches, under cummerbunds, behind front flaps, or anywhere with sufficient hook-and-loop Velcro. Choose a spot where the wedge lies flat against the loop and the knife will not press into your body or block access to other gear.
  3. 3. Test the sandwich before adding the sheath: Slide the platform into the loop field and press it down. Because the design relies on hook-and-loop rather than straps, the hold depends on how much loop surface the wedge covers. If the field is too small or the wedge overhangs, move it.
  4. 4. Attach the sheath with the supplied Chicago screws: The kit includes two 1/4” Chicago screws. Align the sheath holes with the platform slots, pass the screws through, and tighten. The record does not specify a torque value, so tighten by feel and check the fit before loading the knife.
  5. 5. Verify hardware fit and source your own if needed: The supplied hardware may or may not work for your particular application, and you may need to procure your own hardware. If the Chicago screws are too short or the hole pattern does not match, plan for a hardware run before you field the setup.

Placement choices and what each one changes

The KnifenookTM can go in several locations, but each one trades off differently. The record names the locations without ranking them, so the tradeoffs below come from how those locations work on a carrier, not from a manufacturer recommendation.

  • Inside a Kangaroo-style pouch: Keeps the knife concealed and close to the body. Check that the pouch's loop field is large enough for the wedge and that the pouch still closes with the sheath in place.
  • Under a cummerbund: Puts the knife low and out of the way of chest-mounted gear. Make sure the cummerbund's loop surface covers the wedge and that the cummerbund still sits flat over it.
  • Behind a front flap: Useful when you want the knife accessible but not visible. Confirm the flap's loop field and that the sheath does not interfere with the flap's closure.
  • Anywhere with sufficient hook-and-loop Velcro: The platform is not limited to the named locations. The limiting factor is loop surface area and whether the wedge can sit flat without overhanging.

Color, version, and what may arrive

The KnifenookTM is available in Coyote Brown and Black. The product record also carries a disclaimer: the design is unchanged, but the color of the thermoplastic may vary from the images shown, and you may receive the updated version in your shipment. If color matching matters to your kit, treat the swatch as a guide rather than a guarantee.

That disclaimer is the only version note in the record. It does not describe functional changes between versions, so there is nothing in the supplied information to suggest the mounting dimensions differ.

Checkpoints before you load the knife

Once the platform and sheath are assembled, run a few checks that the record's facts support. Confirm the sheath is within the 3.0” width limit and that its holes align with the 0.5” vertical spacing. Press the platform into the loop field and look for overhang at the edges. Tighten the Chicago screws and confirm the sheath does not rock on the platform. Finally, confirm the supplied hardware actually holds your sheath; if it does not, the record explicitly allows for procuring your own.

The supplied information does not include a torque specification, thread-locking guidance, a retention rating, or a list of carriers confirmed to work with the KnifenookTM. Those gaps are decision limits, not product flaws. If your setup depends on any of them, verify with the manufacturer before you rely on the mount.

Related Articles

Customer Service
Home
Products
Cart
Profile